Skip to content

Resource · Public

A Position-Size Calculator Guide with a Pre-Order Check

Validate a sizing result with explicit units, costs, rounding and a fresh cash-loss check, using a fictional account-currency example.

Published

At a glance

A calculator can size the wrong thing perfectly if one input is mistaken. Rebuild a fictional order size from its loss budget, then check omitted costs, allowed increments and the difference between a planned loss and an execution guarantee.

A fictional sizing check subtracts fixed costs, calculates 22,222.22 units and rounds down to a 63.40 USD loss estimate.
Hypothetical assumptions; the stress allowance does not guarantee the maximum possible loss.
Image credit

Hypothetical assumptions; the stress allowance does not guarantee the maximum possible loss.

FavAcademy · Original FavAcademy educational illustration; public use authorized

01

Treat the output as a proposal to verify

A position-size calculator turns assumptions into a quantity. It does not know whether the loss budget is affordable, whether the exit condition is sensible or whether an ordinary stop will fill at the intended price. Write those decisions separately before accepting an output. A polished ticket should not conceal unresolved assumptions.

This guide checks a fictional calculator result rather than introducing the idea of sizing from scratch. The method uses a quote-currency account to avoid a hidden conversion. Real products can require extra contract multipliers, currency conversion and venue-specific increments. If the tool's definition of size is unclear, stop the comparison and resolve it before treating any number as an order-ready quantity.

02

Freeze the budget and price assumptions

Assume an invented planned loss budget of 64 USD. The proposed position has a 25-pip distance from entry to the planned exit, with one pip equal to 0.0001 USD per base unit. We also reserve 2 pips for a stated slippage stress and 4 USD for a separately charged fixed commission.

These are educational assumptions, not recommended limits or current terms. The 2-pip reserve is a stress allowance, not a worst-case guarantee. A larger gap can exceed it. The figure of 64 is an input chosen for the exercise; it does not establish an appropriate fraction of any reader's account or a level of loss that the reader can afford.

03

Convert the budget into a raw quantity

Subtract the fixed 4 USD charge first, leaving 60 USD for the size-dependent loss. The combined assumed price distance is 27 pips. At 0.0001 USD per pip per unit, the loss allowance is 0.0027 USD per unit. Dividing 60 by 0.0027 gives approximately 22,222.22 base units.

Check the dimensions: USD divided by USD per unit leaves units. If the calculator returns lots instead, translate them using the actual contract definition. Do not assume every product uses the same lot size. The illustration keeps the fixed-cost subtraction, per-unit calculation and final quantity in separate stages so each input can be checked rather than hidden inside one unexplained result.

04

Apply an allowed size increment

For this fictional platform, assume orders must be multiples of 1,000 units. Rounding the raw quantity down gives 22,000. Rounding up to 23,000 would exceed the stated budget under the same assumptions. A calculator's default rounding behaviour therefore matters even when its unrounded answer is correct.

Confirm actual minimums and increments in the applicable instrument specification. If the smallest permitted size exceeds the budget, the answer is not to round up and call the trade close enough. The proposed transaction does not fit the stated constraints. A tool should expose that mismatch. Likewise, a zero or negative remaining budget after fixed costs does not supply a usable positive size.

05

Recompute the cash loss from the ticket

At 22,000 units, the planned 25-pip price loss is 55 USD. The 2-pip stress allowance contributes 4.40 USD, and the fixed commission contributes 4 USD. The total is 63.40 USD, leaving 0.60 below the invented 64 USD budget. At 23,000 units, the same calculation gives 66.10 USD.

Perform this reverse check using the size actually shown on the proposed ticket, not the unrounded calculator output. A manual transcription error or a lot-unit mismatch can enter after the original calculation. Confirm the direction and stop price too. A stop entered on the wrong side of the market can create a different instruction rather than the loss scenario you intended to assess.

06

Check which costs are already included

If the stop distance was measured from actual entry fill to an executable closing price, some spread effect may already be embedded. If it was measured between mid-prices, a separate cost treatment may be needed. Write the convention explicitly rather than adding a generic spread allowance to every result and risking double counting.

Inspect commission minimums, financing if relevant and currency-conversion charges. A fixed 4 USD charge is only the assumption used here. Actual fees may vary with size or account type, changing the equation. A calculator that ignores them is not necessarily broken; it may answer a narrower question. The user must understand that scope before interpreting the result as a complete planned loss estimate.

07

Test invalid and changing inputs

Deliberately check a zero stop distance, a negative budget, a missing conversion rate and a size below the product minimum. The workflow should reject or flag these cases, not produce a meaningful-looking quantity by silently replacing inputs. Save the expected handling before testing. This article supplies an acceptance exercise rather than claiming that a specific named calculator passed it.

Also test what happens if a live price field updates while you are reviewing the ticket. Keep a timestamped snapshot of the inputs used. If entry or stop changes materially, recompute rather than carrying forward the old size. A saved output is tied to its assumptions, not permanently valid simply because the account balance has not changed.

08

Keep the limitation beside the answer

The defensible result is 22,000 units under the stated hypothetical costs, increment and price assumptions, with an estimated stressed loss of 63.40 USD. It is not a maximum possible loss. Gaps, illiquidity, contract changes or provider failure can create outcomes outside this simple model, and affordability remains a separate judgement.

Before an actual order, verify the contract, allowed size, account currency, current input values and operational state through the real service. If those cannot be confirmed, the output is not ready to use. A useful calculator check ends with a traceable quantity and its limitations together, rather than a number detached from the conditions that produced it.

FavAcademy’s Position size calculator excludes fees, spreads, slippage and gaps from its native result. To reproduce this separate stress exercise, use the adjusted 60 USD budget, the explicitly stressed 27-pip distance, 100,000 units per lot and a 0.01-lot step. The tool floors lots before recomputing risk and returns 22,000 units with 59.40 USD of modeled price loss. Add the reserved 4 USD fixed commission outside the tool to reach 63.40. The adjustment is our stated exercise, not an automatic cost feature.

Continue learning with Size a Position from the Loss You Can Accept and A Pip-Value Calculator Guide for Different Account Currencies.

Risk disclosure

Educational examples are hypothetical. Costs, execution and product terms vary; no outcome or suitability is promised.